Jalopnik

MARCH 12, 2024

A United Airlines Boeing 777-300 was forced to return to Sydney Kingsford Smith Airport in Australia after takeoff due to a mechanical issue. It appears that hydraulic fluid was gushing from the right landing… Read more. United Flight 830 was at the start of a 13-and-a-half-hour flight across the Pacific Ocean to San Francisco.

Hydraulics 63

Hydraulics Mechanic IT 63

Brake & Front End

FEBRUARY 9, 2024

Using brake pressure gauges proves handy for diagnosing uneven hydraulic pressure. They can measure hydraulic pressure side by side, offering insights into ABS units, master cylinders, and proportioning valves. Loose caliper hardware or worn/misadjusted wheel bearings can cause uneven brake application, resulting in a pull.

Hydraulics 130

Hydraulics Parts Replacement Mechanic Car 130

Tomorrow's Technician

FEBRUARY 8, 2024

Using brake pressure gauges proves handy for diagnosing uneven hydraulic pressure. They can measure hydraulic pressure side by side, offering insights into ABS units, master cylinders, and proportioning valves. Loose caliper hardware or worn/misadjusted wheel bearings can cause uneven brake application, resulting in a pull.

Hydraulics 130

Hydraulics Parts Replacement Mechanic Car 130

Tire Review Magazine

FEBRUARY 26, 2024

Hybrids prioritize using regenerative braking, so the pedal acts more like an input to the ABS module requesting braking force rather than a direct hydraulic pressure request. Under normal operation, hydraulic brake pressure comes from the ABS module’s electric pump motor, not the driver’s foot, providing a consistent pedal feel.

Hydraulics 52

Hydraulics IT Electricity Education 52

Tire Review Magazine

FEBRUARY 26, 2024

Hybrids prioritize using regenerative braking, so the pedal acts more like an input to the ABS module requesting braking force rather than a direct hydraulic pressure request. Under normal operation, hydraulic brake pressure comes from the ABS module’s electric pump motor, not the driver’s foot, providing a consistent pedal feel.

Hydraulics 52

Hydraulics IT Electricity Education 52

Brake & Front End

DECEMBER 14, 2023

Some hybrid systems apply the hydraulic brakes at lower speeds. Normally, the fluid pressure for the wheel hydraulics is generated by the pump and/or accumulator in the ABS HCU or a stroke simulator, and is regulated by the teamed efforts of the ABS and the PCM’s logic. This is called “manual mode.”

Hydraulics 130

Hydraulics Electronics Vehicle Engineering 130

Tomorrow's Technician

JANUARY 8, 2024

In the late 1980s, many cars now had wide front tires and it was difficult to route hydraulic lines from the engine bay to the front of the vehicle and the rack. Many of the first systems were electro-hydraulic with a electric motor powering a hydraulic pump.

Electricity 244

Electricity Hydraulics Software Vehicle 244

Tomorrow's Technician

FEBRUARY 1, 2024

To correct this type of wear, take the same steps as fixing outer pad wear as well as inspecting the hydraulic brake system and the caliper for residual pressure and guide pin hole or piston boot damage, respectively. Mechanical attachment of the friction material can give an extra layer of safety.

Hydraulics 246

Hydraulics Mechanic IT Engineering 246

Tomorrow's Technician

JANUARY 11, 2024

Jason Stott developed his expertise in diesel mechanics and hydraulics under the guidance of his father growing up. Following high school, his passion for truck pulling led him to explore opportunities to cover the costs associated with competitions and truck maintenance.

Engineering 130

Engineering Diesel Mechanics Hydraulics Trucking 130

RepairSmith

FEBRUARY 1, 2024

However, power steering failure in an electric or hydraulic power steering system can make normal steering challenging and risky. Go slow, keep a strong grip on the wheel, and get to a mechanic or call a mobile one for help. How Do I Keep the Power Steering in Good Shape? Can You Drive Without Power Steering ? Look for signs of a leak.

Hydraulics 52

Hydraulics IT Electricity Mechanic 52

Tomorrow's Technician

JANUARY 16, 2024

This article is courtesy of Engine Builder by Evan Laux Jason Stott developed his expertise in diesel mechanics and hydraulics under the guidance of his father growing up. Following high school, his passion for truck pulling led him to explore opportunities to cover the costs associated with competitions and truck maintenance.

Engineering 130

Engineering Diesel Mechanics Trucking Hydraulics 130

Tomorrow's Technician

FEBRUARY 21, 2024

Shifting is controlled by the DCT electronics/hydraulic module on the side of the transmission. The calibration procedure ensures that the neutral positions and mechanical end stops will be learned and saved in the transmission control module.

Engineering 130

Engineering Hydraulics Electronics Mechanic 130

Brake & Front End

FEBRUARY 1, 2024

In between, you have a mixture of mechanical and hydraulic components that magnify the leg muscles of the driver. Brake Booster Math A booster increases the force of the pedal, so a lower mechanical pedal ratio can be used. 1 to 4:1 mechanical pedal ratio. On the hydraulic side, you have the master cylinder and calipers.

Engineering 130

Engineering Hydraulics Mechanic Electricity 130

Brake & Front End

JANUARY 19, 2024

Most later-model vehicles with a manual transmission use a hydraulicsystem consisting of the clutch master cylinder, hydraulic hoses, the concentric slave cylinder and the concentric slave cylinder bearing to actuate the clutch. Clutch problems can occur at almost any mileage and for a wide variety of reasons.

Hydraulics 130

Hydraulics Manufacturing Technical Vehicle 130

Tomorrow's Technician

JANUARY 19, 2024

Most later-model vehicles with a manual transmission use a hydraulicsystem consisting of the clutch master cylinder, hydraulic hoses, the concentric slave cylinder and the concentric slave cylinder bearing to actuate the clutch. Clutch problems can occur at almost any mileage and for a wide variety of reasons.

Hydraulics 130

Hydraulics Manufacturing Technical Vehicle 130

Automotive Training Centre

APRIL 17, 2024

Pulling involves using specialized jigs, clamps, and hydraulic pulling systems to exert controlled force on the bent frame sections. The post 5 Essential Best Practices for Frame Repair After Auto Body Training appeared first on Auto Mechanic Training School | Automotive Training Centre. Are you interested in our automotive training

Body Repair 200

Body Repair Auto Mechanic Training Automotive Hydraulics 200

Tomorrow's Technician

OCTOBER 30, 2023

Code 2A32 (P1014) refers to an eccentric sensor issue Code 2A37 (P1017) also refers to an eccentric sensor issue Code 2A45 (P103A) refers to an actuator motor malfunction The transfer case is a rather unique design in the way that it operates a clutch pack mechanically, not hydraulically, somewhat like a GM.

Check Engine Light 246

Check Engine Light Hydraulics Engineering Software 246

RepairSmith

MAY 13, 2024

As such, it includes the following: Visual inspection: The mechanic looks at the master cylinder , power booster, brake lines, vacuum hose, and combination valve (valve that distributes hydraulic pressure between the front and rear brakes.) Wheel inspection: The mechanic will inspect the wheel bearings for excessive movement.

IT 52

IT Mechanic Auto Repair Fluid Check 52

C and C Automotive

MAY 10, 2024

Leaking Shock Absorbers: Shock absorbers contain hydraulic fluid to dampen suspension movement. Your mechanic can inspect the bushings and replace them as needed. Leaks in the shocks can reduce damping effectiveness, causing excessive bouncing and a harsh ride.

Hydraulics 52

Hydraulics Auto Repair Vehicle Mechanic 52

Tomorrow's Technician

DECEMBER 14, 2023

This will release or bleed off the hydraulic pressure that is holding the wheel. HCU MECHANICAL PROBLEMS Mechanical issues with the HCU are rare, but they can happen. If the system senses a wheel is locked, the inlet/isolation solenoid is closed to prevent any more pressure from the master from reaching the wheel.

Hydraulics 130

Hydraulics Mechanic Vehicle Electronics 130

Brake & Front End

NOVEMBER 6, 2023

Code 2A32 (P1014) refers to an eccentric sensor issue Code 2A37 (P1017) also refers to an eccentric sensor issue Code 2A45 (P103A) refers to an actuator motor malfunction The transfer case is a rather unique design in the way that it operates a clutch pack mechanically, not hydraulically, somewhat like a GM.

Check Engine Light 130

Check Engine Light Hydraulics Engineering Software 130

Tire Review Magazine

DECEMBER 4, 2023

Use compressed air to regularly blow out slip plates and keep mechanisms clear of debris while doing service. Have a certified lift specialist inspect cables, pulleys and pins and check for troublesome hydraulic leaks. Lift racks are especially vulnerable to the harsh winter elements. Wheel balancers need regular cleaning too.

Hydraulics 97

Hydraulics Mechanic Vehicle IT 97

Tire Review Magazine

DECEMBER 4, 2023

Use compressed air to regularly blow out slip plates and keep mechanisms clear of debris while doing service. Have a certified lift specialist inspect cables, pulleys and pins and check for troublesome hydraulic leaks. Lift racks are especially vulnerable to the harsh winter elements. Wheel balancers need regular cleaning too.

Hydraulics 97

Hydraulics Mechanic Vehicle IT 97

Master Mechanics

AUGUST 19, 2023

Yet, like any complex mechanism, it’s susceptible to malfunctions and issues that can hinder its seamless operation. It’s a multifaceted assemblage of sensors, actuators, hydraulic components, and software algorithms that collaborate in real-time to deliver a driving experience that adapts to varying road conditions and driver preferences.

Software 52

Software Hydraulics Master Mechanic Mechanic 52

RepairSmith

SEPTEMBER 29, 2023

Fluid Leaks Seals in the damping system of a strut can wear out, causing hydraulic fluid leaks. You may notice oil or grime on the strut’s hydraulic cylinder due to a leak. Professional Diagnosis Here are the steps a mechanic will follow to diagnose the worn struts: Open the hood and locate the strut mounts.

Hydraulics 52

Hydraulics Mechanic Car Inspection Vehicle 52

Brake & Front End

OCTOBER 9, 2023

806 words can’t cover how this physical proximity wireless access would work or the obligations of the OEM to make mechanical information available. They are not told the brakes must use disc brakes or hydraulics. If a vehicle with drum brakes and mechanical linkages can stop within the mandated distance, it passes the test.

Vehicle 130

Vehicle Hydraulics Mechanic Manufacturing 130

RepairSmith

MAY 14, 2024

In such cases, mechanics may need to remove the wheel, disassemble the brake drum or caliper, and then replace the worn brake pad or shoe. Service brakes are hydraulically operated, which helps in deceleration and stopping while driving. Is it Safe to Drive with a Malfunctioning Emergency Brake ?

Brake Repair 52

Brake Repair Auto Repair Auto Repair Shop Mechanic 52

RepairSmith

MAY 12, 2024

A regular brake fluid flush ensures the hydraulic fluid can handle the pressure of the braking system and make your drive safe. But, if changing the fluid yourself sounds cumbersome, AutoNation Mobile Service mechanics can do it for you. Our mechanics can perform a brake inspection and replace the fluid right from your driveway.

IT 52

IT Tire Rotations Mechanic Brake Repair 52

Tire Review Magazine

MARCH 7, 2024

During normal braking, the pressure from the master cylinder passes through the Hydraulic Control Unit (HCU) unaltered. The wheel may start to turn as a result, but if the wheel doesn’t begin rotating, the outlet or dump valve opens to release the hydraulic pressure holding the wheel.

Hydraulics 52

Hydraulics Preventative Maintenance Electronics Vehicle 52

Master Mechanics

FEBRUARY 14, 2023

A surefire way to ruin the pleasure of a good drive is a mechanical malfunction. It is responsible for storing and releasing compressed hydraulic fluid , which is used to regulate the vehicle’s suspension and brakes. If this warning light appears, it is important to take the vehicle to a professional mechanic as soon as possible.

Master Mechanic 40

Master Mechanic Hydraulics Mechanic Auto Repair 40

RepairSmith

APRIL 26, 2024

The mechanic might also check the pulley bearings since they, too, can produce a squealing noise. When that happens, it’s best to have a mechanic look at it. So, visit a mechanic to fix the leaks. It’s best to visit a mechanic and get the damaged parts replaced.

Car 52

Car Engineering Mechanic Hydraulics 52

AutoSuccess

DECEMBER 8, 2023

The PL-6000DC uses dual telescoping direct-drive hydraulic cylinders to deliver better reliability, smoother operation, and lower maintenance than lifting chains or screw mechanisms. The PL-6000DC’s compact footprint and ganged column design lets you optimize a parking area. Plus, it’s easy and economical to operate.”

Hydraulics 52

Hydraulics Automobile Mechanic Trucking 52

Brake & Front End

OCTOBER 9, 2023

To correct this type of wear, take the same steps as fixing outer pad wear as well as inspecting the hydraulic brake system and the caliper for residual pressure and guide pin hole or piston boot damage, respectively. Mechanical attachment of the friction material can give an extra layer of safety.

Hydraulics 130

Hydraulics Mechanic IT Engineering 130

Brake & Front End

JUNE 30, 2023

When the spool valve has torque applied to it, the openings get larger to apply more hydraulic force. Most tensioners have a dampener mechanism inside or connecting to the arm. This makes the pump work harder to generate more volume and pressure. This also creates heat. Many pumps fail because the belt tensioner was not replaced.

Engineering 223

Engineering Hydraulics Insurance Mechanic 223

RepairSmith

NOVEMBER 29, 2023

Valve Train Noise The valve train comprises numerous components like valves, hydraulic lifters, and pushrods working to control the flow of air and fuel to the cylinders. Similarly, a hydraulic lifter can create a lifter tick. Even vehicles with solid lifters (mechanical lifters) can tick during cold starts. Let’s get started.

Car 52

Car Engineering Hydraulics Oil Change 52

Tomorrow's Technician

APRIL 1, 2024

Two years later, QMA introduced a hydraulic tubing bender for muffler shops, and Henthorn was inspired to change the company name to match. Henthorn took his responsibility for the safety of millions of mechanics around the world very seriously and was committed to ensuring that BendPak produced superior products. “We

Manufacturing 130

Manufacturing Hydraulics Management Automotive Services 130

Brake & Front End

APRIL 1, 2024

Two years later, QMA introduced a hydraulic tubing bender for muffler shops, and Henthorn was inspired to change the company name to match. Henthorn took his responsibility for the safety of millions of mechanics around the world very seriously and was committed to ensuring that BendPak produced superior products. “We

Manufacturing 130

Manufacturing Hydraulics Management Automotive Services 130